Page 1 of 4 123 ... LastLast
Results 1 to 15 of 59

Thread: Barney Resurrection

  1. #1
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Barney Resurrection

    Resurrection of Barney...

    Day Juan
    Out with the old









    I would like to thank my sponsors, Harbor Freight Tools and Burger King. This would not be possible without their support!

    NP Fabrication
    Last edited by NickP3d; 12-02-2017 at 05:46 PM.
    NP Fabrication

  2. #2
    Join Date
    May 2013
    Location
    A J U S A
    Posts
    5,587

    Re: Barney Resurrection

    What happen to Barney?!
    Get Down With the Sickness!

  3. #3
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    Quote Originally Posted by Bugs View Post
    What happen to Barney?!
    More like what didn't happen to Barney!


    NP Fabrication
    NP Fabrication

  4. #4
    Join Date
    May 2013
    Location
    A J U S A
    Posts
    5,587

    Re: Barney Resurrection

    wan-tons?
    Get Down With the Sickness!

  5. #5
    Join Date
    Sep 2006
    Location
    Mesa
    Posts
    3,110

    Re: Barney Resurrection

    Oh, took me a minute to figure out, I thought you were pulling the motor.
    82 Cherokee WT SOA/SF/high steer/Alcan springs/agr box/Borgeson steering shaft/AMC 401/performer/holley TA/HEI/BeCool/727/ALTAS (2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave, Discs, ARB,Artec Truss)/MTR 37X12.5/Corbeau Moab Seats/RCI 6point Harness/Hella Aux lights/tuffy console/killer32 sliders/custom bumpers and roll bar/WARN 8000/steering brace/CO2 Tank/CB/dual batts/custom TC skid plate

  6. #6
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    Tested Compression this morning, 130 across the board. With 200k miles guessing it has been rebuilt. Need to figure out what is causing low oil pressure

    Anybody have a stock pinion arm, and steering knuckles? Also looking for exhaust manifold for 4.0...

    Quote Originally Posted by Bugs View Post
    wan-tons?
    Eventually. For now beefing up the 30




    NP Fabrication
    NP Fabrication

  7. #7
    Join Date
    Dec 2003
    Location
    NW Phoenix
    Posts
    1,233

    Re: Barney Resurrection

    Quote Originally Posted by NickP3d View Post
    I would like to thank my sponsors, Harbor Freight Tools, L Girls, Burger King, and The Clinton Campaign. This would not be possible without their support
    What, no beer sponsor?

  8. #8
    Join Date
    May 2013
    Location
    A J U S A
    Posts
    5,587

    Re: Barney Resurrection

    Quote Originally Posted by NickP3d View Post
    Tested Compression this morning, 130 across the board. With 200k miles guessing it has been rebuilt. Need to figure out what is causing low oil pressure

    Anybody have a stock pinion arm, and steering knuckles? Also looking for exhaust manifold for 4.0...

    Eventually. For now beefing up the 30

    NP Fabrication
    I had oil pressure drop all of a sudden, hooked up a manual oil gage and found it to be a bad sensor. I assume you have already done that?
    Get Down With the Sickness!

  9. #9
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    Quote Originally Posted by Bugs View Post
    I had oil pressure drop all of a sudden, hooked up a manual oil gage and found it to be a bad sensor. I assume you have already done that?
    What is weird is that it fluctuates, at idle it shows low, but the second you run higher RPM it goes back to normal. Would a bad sensor do that?


    NP Fabrication
    NP Fabrication

  10. #10
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    Quote Originally Posted by roger View Post
    What, no beer sponsor?
    Sadly our legal department advised against it after last years karaoke incident...


    NP Fabrication
    NP Fabrication

  11. #11
    Join Date
    May 2013
    Location
    A J U S A
    Posts
    5,587

    Re: Barney Resurrection

    Exactly what mine was doing. I got the tester at HF.

    Or stop by and borrow mine?

    Sent from my iPhone using my ****
    Get Down With the Sickness!

  12. #12
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    Quote Originally Posted by Bugs View Post
    Exactly what mine was doing. I got the tester at HF.

    Or stop by and borrow mine?

    Sent from my iPhone using my ****
    I'll make a trek over to your side of town one day!


    NP Fabrication
    NP Fabrication

  13. #13
    Join Date
    May 2013
    Location
    A J U S A
    Posts
    5,587

    Re: Barney Resurrection

    Quote Originally Posted by NickP3d View Post
    Sadly our legal department advised against it after last years karaoke incident...


    NP Fabrication

    Surprised that stayed out of the media!
    Get Down With the Sickness!

  14. #14
    Join Date
    Aug 2013
    Location
    Phoenix
    Posts
    873

    Re: Barney Resurrection

    First order of business, get this to turn this. Thinking about using an industrial garden hose as a hydraulic line... Any other opinions?




    NP Fabrication
    NP Fabrication

  15. #15
    Join Date
    Jan 2014
    Location
    Arizona
    Posts
    1,027

    Re: Barney Resurrection

    Quote Originally Posted by NickP3d View Post
    What is weird is that it fluctuates, at idle it shows low, but the second you run higher RPM it goes back to normal. Would a bad sensor do that?


    NP Fabrication
    Corrosion where the sensor threads into the block will do that. Or corrosion on one of the electrical connections. Or a bad sensor could as well.

    Lunatic Fridge.

    Sent from the FrankenHeep
    Quote Originally Posted by 4wheelinHawkeye View Post
    Welll... I might fall under the category "special" kinda crazy. Wait, what ? Did I just say....
    Quote Originally Posted by LO PHAT View Post
    You will fit right in with my group of misfits. I'll even make them promise to flop you gently.
    Quote Originally Posted by Oscar_Mike 2013 View Post
    Yup, I'm a crab. Crabs make me feel dirty.

Page 1 of 4 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Nothing says "Backcountry" like a Barney purple Jeep
    By MrBreeze in forum General Discussion
    Replies: 19
    Last Post: 12-30-2015, 07:03 AM
  2. The Resurrection
    By Heaney in forum New Jeep Owners Forum (or new to the club)
    Replies: 10
    Last Post: 01-08-2014, 01:11 PM
  3. CJ resurrection stuff needed
    By OlneyJeeps in forum Wanted
    Replies: 5
    Last Post: 05-05-2013, 01:54 PM
  4. Resurrection
    By Len in forum Old Jeeps and Stock Restorations
    Replies: 23
    Last Post: 10-07-2012, 08:49 PM
  5. Resurrection of Battery thread
    By FourxDad in forum Non-Jeep Items Wanted
    Replies: 1
    Last Post: 10-25-2011, 08:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •