blooddrive
01-03-2004, 11:07 AM
18245-18269
18245 From: Greg Stapley <love24wheel@h...>
Date: Fri Feb 2, 2001 3:33pm
Subject: Re: Re: Heres one for You Guys (A Must See)
That thing has aas much power as my 4 cyl.
Greg
>From: "James Towle"
>To: az_vjc@yahoogroups.com
>Subject: [az_vjc] Re: Heres one for You Guys (A Must See)
>Date: Fri, 02 Feb 2001 18:36:52 -0000
>
>You could buy the real thing for what those cost.....(?)
>
>--James
>
>--- In az_vjc@y..., "JEEP THANG" wrote:
> > CHeck OUt this Guys Stuff, Maybe they would be willing to make some
> > miniature rockcrawlers, wouldn't that be cool.
> >
> > http://www.viper-v10.com/
> > http://www.conleyprecision.com/
> >
> > Sincerely: Larry George
> > JEEP THANG
>
>
>
>
--------------------------------------------------------------------------------
Get your FREE download of MSN Explorer at http://explorer.msn.com
--------------------------------------------------------------------------------
ADVERTISEMENT
18246 From: Ralph Williams <ralph@p...>
Date: Fri Feb 2, 2001 4:58pm
Subject: [Fwd: RE: DIFFICULTY OF PLEASANT TO CROWN KING]
Argh! Hate when people post in HTML. Oh well.
There is a by-pass to "the ledge". It is about 10 miles further
to Crown King.
About 1/2 mile before "the ledge" in the bottom of the wash, take
a left. Follow that road. it is a nice drive, some cool old
machinery to look at and the road is much better.
Ralph
-------- Original Message --------
Subject: RE: [az_vjc] DIFFICULTY OF PLEASANT TO CROWN KING
Date: Fri, 2 Feb 2001 07:38:49 -0800 (PST)
From: Scott Kruize <osmtj@y...>
To: Stu Olson <solson8@q...>, pdjpn@a...,
az_vjc@yahoogroups.com
Normally Crown King is a piece of cake in a stock Jeep. There is
one ledge that has been worse than usual the past 6 months.
Somebody finally removed the ramp of rocks here and alot of
vehicles turn back. The last couple times up I had to winch a
couple vehicles over it. There usually is ice on the portion of
the trail. One TJ has rolled of the cliff next to this obstacle
recently, though I don't think it was an AZVJC member. One of the
vehicles I winched, a Dodge Ram had his rear tires hanging off
the dropoff. Another one, a YJ had both drivers side tires
hanging off. We managed to get both back onto the trail with the
use of a snatch block and winch. Be extremely careful on this
obstacle this time of year! Be sure to travel with others.
Scott
Stu Olson <solson8@q...> wrote:
It is very hard to "run" from Lake Pleasant to Crown
King, as it is well over 30 miles and uphill most of
the way. <G>However, your YJ is capable of getting
through the trail. My first time on that trail was
with less than what you have.Stu
Stu Olson N7QJP
Phoenix, AZ
http://www.stu-offroad.com
http://www.users.uswest.net/~solson8
-----Original Message-----
From: pdjpn@a... [mailto:pdjpn@a...]
Sent: Thursday, February 01, 2001 22:28
To: az_vjc@yahoogroups.com
Subject: [az_vjc] DIFFICULTY OF PLEASANT TO
CROWN KING
HOW HARD IS IT TO RUN FROM PLEASANT TI
CROWN KING?
I HAVE A 90 YJ WITH A 84,000 MILE 4 CYLINDER
ENGINE. THE ONLY THING
I REALLY HAVE ON IT IS A 4'' PRO COMP SPRING
LIFT, 31 13.50 SWAMPERS
AND SOME KC'S. SHOUKD I BE WORRIED ABOUT THE
RED ROCK!
I WANT TO DO THE TRAIL BUT NOT SURE IF I CAN
PAUL
-----------------------------------------------------------------
Do You Yahoo!?
- Get personalized email addresses from Yahoo! Mail Personal
Address - only $35 a year!
18247 From: Rick Hall <ricknhall@h...>
Date: Fri Feb 2, 2001 5:20pm
Subject: Toybox??
I fired off an email to Toybox on Monday and still haven't heard back. Of
those who have done business with them do you know if they have a shop that
stocks parts or are they strictly mail order?
Rick
18248 From: Joe W <arizonajeep@h...>
Date: Fri Feb 2, 2001 5:41pm
Subject: I'm forwarding this Coupon to the group just in case some of you could use it.
Just in case someone on the list could use these.
Joe West
-----Original Message-----
From: Harbor Freight Tools - USA [mailto:mktdelano@harborfreight.com]
Sent: Thursday, February 01, 2001 8:41 AM
To: arizonajeep@home.com
Subject: HERE IS YOUR VALUABLE COUPON!!!
YOUR LOCAL HARBOR FREIGHT TOOLS
STORE INVITES YOU TO SAVE EVEN MORE
IN 3 EASY STEPS
1. Print out this email.
2. Bring it to a Harbor Freight Tools store near you.
3. Take advantage of savings like those shown below
and save up to an additional $10 !
Locate a Store Near You
Print this coupon and take it to your nearest Harbor Freight Tools store. One coupon per customer.
--------------------------------------------------------------------------------
Bigfoot Hand Truck
Reg. $49.99 SALE $24.99
Super quality 700 pound capacity hand truck features long axle braces for easy stair climbing, heavy gauge toe plate with rounded corners, beveled front, and ''P'' shaped safety handle. Big 13'' pneumatic tires ride on heavy duty ball bearing hubs. Lot No. 37520
--------------------------------------------------------------------------------
15 pc. Tungsten Carbide Tipped Router Bit Set
Reg. $39.99 SALE $29.99
Long life tungsten carbide tips and the most used routing shapes. This is the set all serious woodworkers need. Ground to ultra close tolerances for the best finish available. Includes individually organized storage case. Lot No. 31164
--------------------------------------------------------------------------------
18 Volt Cordless 3/8" Drill/Driver with Keyless Chuck!
Reg. $72.99 SALE $49.97
The 18 volt battery on this drill gives you more run time than 14.4 volt cordless drills. Balanced T-handle design helps keep the drill steady as you work. Jacobs keyless chuck for sure grip. Variable speed reversible. Includes charger, 18 volt battery, 6 piece screwdriver bit set, 6 piece drill bit set and carrying case. Lot No. 37144
--------------------------------------------------------------------------------
Power Cutout Tool
Reg. $39.99 SALE $24.99
Better than a jigsaw for making plunge cuts in walls, floors and ceilings. No need to drill pilot holes. HSS spiral bit cuts wood up to 1'', plywood, plastics and paneling. Use with carbide bits (sold separately) to cut through plaster, ceramic wall tile, cement board and fiberglass. High impact housing. Includes: 1/8'' and 1/4'' collets. Lot No. 42831
--------------------------------------------------------------------------------
7 Function Multi-Tester
Reg. $9.99 SALE $4.99
Get accurate readings for DC voltage, DC current, AC voltage, resistance, transistor test, diode test, and continuity response. Features easy-to-read 3-1/2 digit LCD readout, positive set selector switch, and 32" leads. Low battery indication.Fuse and diode protected circuit. Lot No. 30756
--------------------------------------------------------------------------------
Grinder Pedestal
Reg. $49.99 SALE $29.99
Positions your bench grinder where you need it for most efficient use. Heavy duty cast iron construction with large 10" x 10" table and big 3-1/2" diameter tube steel column. Predrilled holes in table allows easy installation of most grinders including most Central Machinery bench grinders. Includes removable water pot. Grinder not included. Lot No.5799
--------------------------------------------------------------------------------
4" X 36" Belt/6" Disc Sander, 1/3hp Motor
Reg. $79.99 SALE $59.99
Adjustable belt sands inside and outside curves. Cast aluminum sanding disc features a cast aluminum table that locks in any angle from 0¡ to 45¡. Table can be repositioned for use with belt or disc.
Includes: 7-1/2'' x 5'' cast aluminum table, miter gauge, and adjustable backstop. Lot No. 5154
--------------------------------------------------------------------------------
Heavy Duty 6 Wheel Creeper
Reg. $24.99 SALE $16.97
Lifetime Warranty
This low-riding creeper lets you glide just 4'' off the ground. 2'' foam padding is easy on your back. Heavy duty vinyl cover wipes clean. Solid nylon castors with ball-bearing swivels roll easily across floors. Offset center wheels let you turn on a dime. Rugged steel frame takes abuse. 37'' long x 18'' wide. Lot No. 36961
--------------------------------------------------------------------------------
8" Bench Grinder with Gooseneck Lamp
Reg. $69.99 SALE $49.97
Rugged capacitor start motor gets up to speed instantly with plenty of power for quick stock removal. Steel sealed ball bearings support the motor shaft for exceptionally long wear. Equipped with medium and course grinding wheels, large adjustable eye shields, spark deflectors, adjustable tool rests.Flexible lamp is 11-1/2'' high. Uses 60 watt bulb (sold separately). Lot No. 37823
--------------------------------------------------------------------------------
Hurry in!!! Prices only good through February 8, 2001!!!
--------------------------------------------------------------------------------
This offer only good at Harbor Freight Tools retail stores.
--------------------------------------------------------------------------------
We hope you enjoyed this sales update. To change your email address,
click on the URL below...
http://www.harborfreight.com/cpi/taf/changeemail.taf?email=arizonajeep@home.com
--------------------------------------------------------------------------------
If you have received this message in error, or if you no longer wish to receive information from Harbor Freight, unsubscribe by clicking below on the URL...
http://www.harborfreight.com/cpi/taf/unsubscribe.taf?email=arizonajeep@home.com
--------------------------------------------------------------------------------
Opt-in for Harbor Freight Tools - USA provided by Harbor Freight Tools - USA
Copyright 2001, Harbor Freight Tools - USA
week5retail
--------------------------------------------------------------------------------
18249 From: <sfugatejeremy75@a...>
Date: Fri Feb 2, 2001 7:19pm
Subject: anyone in tucson???
I just wanted to see if anyone in Tucson wanted to go hit a
trail one weekend?? I just lifted my Jeep and havnt had anyone to go
with (not very fun by yourself!!) If anyone is going somewhere let me
know if you dont mind.
Thanks Jeremy
18250 From: Nick Notestine <nnote@n...>
Date: Fri Feb 2, 2001 11:02pm
Subject: Re: CJ Dana 30 broken....Help!!
The dana 30's in the yj's are reverse cut but the tj's are standard.
Nick
----- Original Message -----
From: "blake shepherd" <blake@b...>
To: "'AZ_VJC'" <AZ_vjc@yahoogroups.com>
Sent: Friday, February 02, 2001 2:40 PM
Subject: [az_vjc] CJ Dana 30 broken....Help!!
>
> Today I removed the diff cover on my dana 30 only to find that the ring
gear
> has a broken tooth. The gear is missing about 1/2 of one tooth (pinion
gear
> is fine). Plus the tooth was not in the case or the fluid........ hmm.
> Before I spend alot of money fixing the dana 30, I would like to know what
> axles I can swap in its place. Will a YJ or TJ dana 30 bolt in or do they
> have a reverse rotation? I have heard of people swapping in scout or
maybe
> early bronco axles. I am looking for help. Does anyone have an entire
dana
> 30 or any other axle that you have laying around that would fit? Any
> comments are appreciated.
>
> TIA
>
> Blake 1980 CJ5 35" BFG'S Chevy 305
>
>
>
>
18251 From: AzVJC Website <azvjc@a...>
Date: Fri Feb 2, 2001 11:08pm
Subject: [TR] Box Canyon - Sunday, February 4, 2001
Hello All,
This is an automated message from the website, please do not reply to it!
Ray B. is leading a Box Canyon trail run on Sunday, February 4, 2001.
When: Meet at 10:00am...air down and hit the trail by 10:45.
Where: Dirt lot just south of the RR Tracks at the North end of
Florence. (Near mile Marker 136 on Hwy 79) Right on Price
Rd.
Rating: 3.0
Length: All Day
CB Channel: 4
We will run through Box Canyon as a warm up, then on to the
Coke Ovens. Gonna give this one more try Hoping for co-
operation from Mother Nature.
Click Here To Add Your Name to the List or For More Information
Thank You,
- The AzVJC Website
18252 From: <jeep108@h...>
Date: Fri Feb 2, 2001 11:24pm
Subject: Good deal on d30 & d44
In todays az rep in the stuff under $100 there was a d44 rear ls rear
out of a 97 tj with 3:55s and front d 30 for $50 each.Good deal if
someone needs one.
Ken
18253 From: Chris <i_shence_2000@y...>
Date: Sat Feb 3, 2001 0:29am
Subject: Trail Rating
Hello,
I'm a new member, I just bought a 98 Wrangler yesterday. I've
passengered many off-roading trips with my friends, but now I finally
get to drive the trails for myself. Everything is really new to me,
I've reading all the info I can on safe 4x4in' and looking at the
photos and stuff. I am curious on trail ratings.. Whats the rating of
Senator Highway? Thats the road that runs from crown king to prescott.
I'm a huge fan of crown king and I hope to someday make the drive up
from pleasent myself. Check out my Crown king fan site, I'll be
updating it soon with recent photos from just last week, and soon
again with photos with my jeep :)
http://i-shence.com/crownking/
Thanks,
Chris benner
18254 From: DougB <azjeep@h...>
Date: Sat Feb 3, 2001 3:45am
Subject: Re: Trail Rating
Welcome aboard!
As to the trail from CK to Prescott...probably a class 2 to 2+. Fine for a
stock Jeep.
Doug
----- Original Message -----
From: "Chris" <i_shence_2000@y...>
To: <az_vjc@yahoogroups.com>
Sent: Saturday, February 03, 2001 1:29 AM
Subject: [az_vjc] Trail Rating
> Hello,
> I'm a new member, I just bought a 98 Wrangler yesterday. I've
> passengered many off-roading trips with my friends, but now I finally
> get to drive the trails for myself. Everything is really new to me,
> I've reading all the info I can on safe 4x4in' and looking at the
> photos and stuff. I am curious on trail ratings.. Whats the rating of
> Senator Highway? Thats the road that runs from crown king to prescott.
> I'm a huge fan of crown king and I hope to someday make the drive up
> from pleasent myself. Check out my Crown king fan site, I'll be
> updating it soon with recent photos from just last week, and soon
> again with photos with my jeep :)
>
> http://i-shence.com/crownking/
>
> Thanks,
> Chris benner
>
>
>
>
>
>
18255 From: Jon Loveless <jonloveless@m...>
Date: Sat Feb 3, 2001 5:08am
Subject: ToyBox
Damon Flippo (ToyBox) operates out of his father-in-laws battery shop off 21st Street and Deer Valley Parkway. His web site is www.ToyBoxoffroad.com . He does stock some parts.
Jon Loveless
(480) 816-6240
18256 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 6:33am
Subject: RE: Trail Rating
Welcome aboard, Chris.
It has been a few years since I was on that part of the Senator near the
Prescott end, but when I last was, I ran it in a stock XJ....pretty scenery,
easy road.
Stu Olson N7QJP
Phoenix, AZ DM33vm
http://www.stu-offroad.com
http://www.qsl.net/n7qjp
http://www.users.uswest.net/~solson8
Developer of VKE Digital Voice Keyer
-----Original Message-----
From: Chris [mailto:i_shence_2000@y...]
Sent: Saturday, February 03, 2001 1:30 AM
To: az_vjc@yahoogroups.com
Subject: [az_vjc] Trail Rating
Hello,
I'm a new member, I just bought a 98 Wrangler yesterday. I've
passengered many off-roading trips with my friends, but now I finally
get to drive the trails for myself. Everything is really new to me,
I've reading all the info I can on safe 4x4in' and looking at the
photos and stuff. I am curious on trail ratings.. Whats the rating of
Senator Highway? Thats the road that runs from crown king to prescott.
I'm a huge fan of crown king and I hope to someday make the drive up
from pleasent myself. Check out my Crown king fan site, I'll be
updating it soon with recent photos from just last week, and soon
again with photos with my jeep :)
http://i-shence.com/crownking/
Thanks,
Chris benner
18257 From: Ken Borer <kborer@i...>
Date: Sat Feb 3, 2001 7:22am
Subject: Box Canyon on Sunday
Ray,
Thanks for the reschedule on this trip - we will see you in the morning.
Ken
76 CJ-5 304 V8
2 1/2" Sagging Lift - 4" Superlift soon
33 X 12.5 on 15 X 10 Rims
Open Both Ends for now
18258 From: TRobertsRN <TRobertsRN@e...>
Date: Sat Feb 3, 2001 7:36am
Subject: Fw: springs
----- Original Message -----
From: TRobertsRN <TRobertsRN@e...>
To: FSJ List <fsj-list@l...>
Sent: Saturday, February 03, 2001 8:30 AM
Subject: springs
Sorry I have been so slow to respond to those interested in my springs from
the 78 Cherokee. I have been very ill, can barely get out of bed, have not
slept in 3 days. Therefore I have not been able to check on shipping price.
I did notice that a couple of you that were interested were in Arizona.
Right now it would make my life a lot easier if one of you could come by and
pick them up.
Thomas Roberts
78 Cherokee WT
Mesa, Arizona
18259 From: <Jeepguy@z...>
Date: Sat Feb 3, 2001 10:11am
Subject: fire stick
Can you paint a Firestick ant with rustoleum paint? does it have any
adverse effects?? I know it is no sat dish, but hey... you never
know!! :)
18260 From: <Jeepguy@z...>
Date: Sat Feb 3, 2001 10:48am
Subject: Firstwater Closed!!
Okay they were easy trails, but fun no less! The Forrest service was
out there putting up the barbwire fences. They had raked the trails
to loosen up the dirt, and put big mounds of dirt in front of the
fences (as if that would stop the almighty jeep)! Anyway, they are
pretty tame hills, but great for beginners and they are gone... all
gone!! :(
18261 From: <sharxjeep@c...>
Date: Sat Feb 3, 2001 6:16am
Subject: Squeeze rock
Has anyone run Squeeze Rock at Sycamore Creek and could they give me some
info on it. Some friends and I were going to go out that way tomorrow and
would like to check it out. Any info would be greatly appreciated, thanks.
Sharky
18262 From: Kelly McCormick <KellyMC@p...>
Date: Sat Feb 3, 2001 3:01pm
Subject: Items for Sale
I still have that Warrior roof rack for sale, in addition to some other
parts the are not neccessarily all for jeeps.
I have four 31" Mudders w/ 6 lug-$500
Any stock parts off a 97 TJ, like springs, snocks, trac bar, tire carrier,
someone is just welcome to have.
I also have a silver camper shell of a 92 Toyota for $500.
Well let me know,
Thanks Kelly
18263 From: Eric Herring <herring@u...>
Date: Sat Feb 3, 2001 3:31pm
Subject: RE: fire stick
I don't know but they do sell them in different colors.
Eric Herring 92XJ
-----Original Message-----
From: Jeepguy@z... [mailto:Jeepguy@z...]
Sent: Saturday, February 03, 2001 11:11 AM
To: az_vjc@yahoogroups.com
Subject: [az_vjc] fire stick
Can you paint a Firestick ant with rustoleum paint? does it have any
adverse effects?? I know it is no sat dish, but hey... you never
know!! :)
18264 From: Greg Mobley <greg85268@y...>
Date: Sat Feb 3, 2001 4:33pm
Subject: Help with teraflex quick disconnect
18265 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 4:46pm
Subject: RE: Help with teraflex quick disconnect
Sure.....but you have to ask a question first!
Stu Olson N7QJP
Phoenix, AZ DM33vm
http://www.stu-offroad.com
http://www.qsl.net/n7qjp
http://www.users.uswest.net/~solson8
Developer of VKE Digital Voice Keyer
-----Original Message-----
From: Greg Mobley [mailto:greg85268@yahoo.com]
Sent: Saturday, February 03, 2001 5:33 PM
To: Jeep Club
Subject: [az_vjc] Help with teraflex quick disconnect
18266 From: Greg Mobley <greg85268@y...>
Date: Sat Feb 3, 2001 5:03pm
Subject: HELP WITH TERAFLEX QUICK DISCONNECT
Hi everyone
I recently had a Teraflex 3 inch lift kit put on and I want to put Teraflex quick disconnects on by myself shop wants $70.00 to install it don't look that difficult what advice could everyone give me.
Thank you
Greg
18267 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 5:10pm
Subject: RE: HELP WITH TERAFLEX QUICK DISCONNECT
Greg,
I'll pass along a spot on my web site you might find helpful.
My install comments and some pics of the Tera QDs at http://www.stu-offroad.com/98jeep_lift/tj_lift2.htm
Feel free to snoop around....you might find some other helpful information.
Later..........Stu
Stu Olson N7QJP
Phoenix, AZ
http://www.stu-offroad.com
http://www.users.uswest.net/~solson8
-----Original Message-----
From: Greg Mobley [mailto:greg85268@yahoo.com]
Sent: Saturday, February 03, 2001 18:04
To: Jeep Club
Subject: [az_vjc] HELP WITH TERAFLEX QUICK DISCONNECT
Hi everyone
I recently had a Teraflex 3 inch lift kit put on and I want to put Teraflex quick disconnects on by myself shop wants $70.00 to install it don't look that difficult what advice could everyone give me.
Thank you
Greg
18268 From: <sharxjeep@c...>
Date: Sat Feb 3, 2001 0:37pm
Subject: Squeeze Rock
Has anyone run Squeeze Rock at Sycamore Canyon and could they give me some
info on it. Some friends and I were going to go out that way tomorrow and
would like to check it out. Any info would be greatly appreciated, thanks.
Sharky
18269 From: Larry T. <lwt002@a...>
Date: Sat Feb 3, 2001 5:54pm
Subject: Member sighting !!
White lifted TJ, Northbound, Alma School North of Southern about
11:20+-AM. Sweet ride!
I was in the black TJ. I waved but it was probably too late for you
to see.
Larry T.
18245 From: Greg Stapley <love24wheel@h...>
Date: Fri Feb 2, 2001 3:33pm
Subject: Re: Re: Heres one for You Guys (A Must See)
That thing has aas much power as my 4 cyl.
Greg
>From: "James Towle"
>To: az_vjc@yahoogroups.com
>Subject: [az_vjc] Re: Heres one for You Guys (A Must See)
>Date: Fri, 02 Feb 2001 18:36:52 -0000
>
>You could buy the real thing for what those cost.....(?)
>
>--James
>
>--- In az_vjc@y..., "JEEP THANG" wrote:
> > CHeck OUt this Guys Stuff, Maybe they would be willing to make some
> > miniature rockcrawlers, wouldn't that be cool.
> >
> > http://www.viper-v10.com/
> > http://www.conleyprecision.com/
> >
> > Sincerely: Larry George
> > JEEP THANG
>
>
>
>
--------------------------------------------------------------------------------
Get your FREE download of MSN Explorer at http://explorer.msn.com
--------------------------------------------------------------------------------
ADVERTISEMENT
18246 From: Ralph Williams <ralph@p...>
Date: Fri Feb 2, 2001 4:58pm
Subject: [Fwd: RE: DIFFICULTY OF PLEASANT TO CROWN KING]
Argh! Hate when people post in HTML. Oh well.
There is a by-pass to "the ledge". It is about 10 miles further
to Crown King.
About 1/2 mile before "the ledge" in the bottom of the wash, take
a left. Follow that road. it is a nice drive, some cool old
machinery to look at and the road is much better.
Ralph
-------- Original Message --------
Subject: RE: [az_vjc] DIFFICULTY OF PLEASANT TO CROWN KING
Date: Fri, 2 Feb 2001 07:38:49 -0800 (PST)
From: Scott Kruize <osmtj@y...>
To: Stu Olson <solson8@q...>, pdjpn@a...,
az_vjc@yahoogroups.com
Normally Crown King is a piece of cake in a stock Jeep. There is
one ledge that has been worse than usual the past 6 months.
Somebody finally removed the ramp of rocks here and alot of
vehicles turn back. The last couple times up I had to winch a
couple vehicles over it. There usually is ice on the portion of
the trail. One TJ has rolled of the cliff next to this obstacle
recently, though I don't think it was an AZVJC member. One of the
vehicles I winched, a Dodge Ram had his rear tires hanging off
the dropoff. Another one, a YJ had both drivers side tires
hanging off. We managed to get both back onto the trail with the
use of a snatch block and winch. Be extremely careful on this
obstacle this time of year! Be sure to travel with others.
Scott
Stu Olson <solson8@q...> wrote:
It is very hard to "run" from Lake Pleasant to Crown
King, as it is well over 30 miles and uphill most of
the way. <G>However, your YJ is capable of getting
through the trail. My first time on that trail was
with less than what you have.Stu
Stu Olson N7QJP
Phoenix, AZ
http://www.stu-offroad.com
http://www.users.uswest.net/~solson8
-----Original Message-----
From: pdjpn@a... [mailto:pdjpn@a...]
Sent: Thursday, February 01, 2001 22:28
To: az_vjc@yahoogroups.com
Subject: [az_vjc] DIFFICULTY OF PLEASANT TO
CROWN KING
HOW HARD IS IT TO RUN FROM PLEASANT TI
CROWN KING?
I HAVE A 90 YJ WITH A 84,000 MILE 4 CYLINDER
ENGINE. THE ONLY THING
I REALLY HAVE ON IT IS A 4'' PRO COMP SPRING
LIFT, 31 13.50 SWAMPERS
AND SOME KC'S. SHOUKD I BE WORRIED ABOUT THE
RED ROCK!
I WANT TO DO THE TRAIL BUT NOT SURE IF I CAN
PAUL
-----------------------------------------------------------------
Do You Yahoo!?
- Get personalized email addresses from Yahoo! Mail Personal
Address - only $35 a year!
18247 From: Rick Hall <ricknhall@h...>
Date: Fri Feb 2, 2001 5:20pm
Subject: Toybox??
I fired off an email to Toybox on Monday and still haven't heard back. Of
those who have done business with them do you know if they have a shop that
stocks parts or are they strictly mail order?
Rick
18248 From: Joe W <arizonajeep@h...>
Date: Fri Feb 2, 2001 5:41pm
Subject: I'm forwarding this Coupon to the group just in case some of you could use it.
Just in case someone on the list could use these.
Joe West
-----Original Message-----
From: Harbor Freight Tools - USA [mailto:mktdelano@harborfreight.com]
Sent: Thursday, February 01, 2001 8:41 AM
To: arizonajeep@home.com
Subject: HERE IS YOUR VALUABLE COUPON!!!
YOUR LOCAL HARBOR FREIGHT TOOLS
STORE INVITES YOU TO SAVE EVEN MORE
IN 3 EASY STEPS
1. Print out this email.
2. Bring it to a Harbor Freight Tools store near you.
3. Take advantage of savings like those shown below
and save up to an additional $10 !
Locate a Store Near You
Print this coupon and take it to your nearest Harbor Freight Tools store. One coupon per customer.
--------------------------------------------------------------------------------
Bigfoot Hand Truck
Reg. $49.99 SALE $24.99
Super quality 700 pound capacity hand truck features long axle braces for easy stair climbing, heavy gauge toe plate with rounded corners, beveled front, and ''P'' shaped safety handle. Big 13'' pneumatic tires ride on heavy duty ball bearing hubs. Lot No. 37520
--------------------------------------------------------------------------------
15 pc. Tungsten Carbide Tipped Router Bit Set
Reg. $39.99 SALE $29.99
Long life tungsten carbide tips and the most used routing shapes. This is the set all serious woodworkers need. Ground to ultra close tolerances for the best finish available. Includes individually organized storage case. Lot No. 31164
--------------------------------------------------------------------------------
18 Volt Cordless 3/8" Drill/Driver with Keyless Chuck!
Reg. $72.99 SALE $49.97
The 18 volt battery on this drill gives you more run time than 14.4 volt cordless drills. Balanced T-handle design helps keep the drill steady as you work. Jacobs keyless chuck for sure grip. Variable speed reversible. Includes charger, 18 volt battery, 6 piece screwdriver bit set, 6 piece drill bit set and carrying case. Lot No. 37144
--------------------------------------------------------------------------------
Power Cutout Tool
Reg. $39.99 SALE $24.99
Better than a jigsaw for making plunge cuts in walls, floors and ceilings. No need to drill pilot holes. HSS spiral bit cuts wood up to 1'', plywood, plastics and paneling. Use with carbide bits (sold separately) to cut through plaster, ceramic wall tile, cement board and fiberglass. High impact housing. Includes: 1/8'' and 1/4'' collets. Lot No. 42831
--------------------------------------------------------------------------------
7 Function Multi-Tester
Reg. $9.99 SALE $4.99
Get accurate readings for DC voltage, DC current, AC voltage, resistance, transistor test, diode test, and continuity response. Features easy-to-read 3-1/2 digit LCD readout, positive set selector switch, and 32" leads. Low battery indication.Fuse and diode protected circuit. Lot No. 30756
--------------------------------------------------------------------------------
Grinder Pedestal
Reg. $49.99 SALE $29.99
Positions your bench grinder where you need it for most efficient use. Heavy duty cast iron construction with large 10" x 10" table and big 3-1/2" diameter tube steel column. Predrilled holes in table allows easy installation of most grinders including most Central Machinery bench grinders. Includes removable water pot. Grinder not included. Lot No.5799
--------------------------------------------------------------------------------
4" X 36" Belt/6" Disc Sander, 1/3hp Motor
Reg. $79.99 SALE $59.99
Adjustable belt sands inside and outside curves. Cast aluminum sanding disc features a cast aluminum table that locks in any angle from 0¡ to 45¡. Table can be repositioned for use with belt or disc.
Includes: 7-1/2'' x 5'' cast aluminum table, miter gauge, and adjustable backstop. Lot No. 5154
--------------------------------------------------------------------------------
Heavy Duty 6 Wheel Creeper
Reg. $24.99 SALE $16.97
Lifetime Warranty
This low-riding creeper lets you glide just 4'' off the ground. 2'' foam padding is easy on your back. Heavy duty vinyl cover wipes clean. Solid nylon castors with ball-bearing swivels roll easily across floors. Offset center wheels let you turn on a dime. Rugged steel frame takes abuse. 37'' long x 18'' wide. Lot No. 36961
--------------------------------------------------------------------------------
8" Bench Grinder with Gooseneck Lamp
Reg. $69.99 SALE $49.97
Rugged capacitor start motor gets up to speed instantly with plenty of power for quick stock removal. Steel sealed ball bearings support the motor shaft for exceptionally long wear. Equipped with medium and course grinding wheels, large adjustable eye shields, spark deflectors, adjustable tool rests.Flexible lamp is 11-1/2'' high. Uses 60 watt bulb (sold separately). Lot No. 37823
--------------------------------------------------------------------------------
Hurry in!!! Prices only good through February 8, 2001!!!
--------------------------------------------------------------------------------
This offer only good at Harbor Freight Tools retail stores.
--------------------------------------------------------------------------------
We hope you enjoyed this sales update. To change your email address,
click on the URL below...
http://www.harborfreight.com/cpi/taf/changeemail.taf?email=arizonajeep@home.com
--------------------------------------------------------------------------------
If you have received this message in error, or if you no longer wish to receive information from Harbor Freight, unsubscribe by clicking below on the URL...
http://www.harborfreight.com/cpi/taf/unsubscribe.taf?email=arizonajeep@home.com
--------------------------------------------------------------------------------
Opt-in for Harbor Freight Tools - USA provided by Harbor Freight Tools - USA
Copyright 2001, Harbor Freight Tools - USA
week5retail
--------------------------------------------------------------------------------
18249 From: <sfugatejeremy75@a...>
Date: Fri Feb 2, 2001 7:19pm
Subject: anyone in tucson???
I just wanted to see if anyone in Tucson wanted to go hit a
trail one weekend?? I just lifted my Jeep and havnt had anyone to go
with (not very fun by yourself!!) If anyone is going somewhere let me
know if you dont mind.
Thanks Jeremy
18250 From: Nick Notestine <nnote@n...>
Date: Fri Feb 2, 2001 11:02pm
Subject: Re: CJ Dana 30 broken....Help!!
The dana 30's in the yj's are reverse cut but the tj's are standard.
Nick
----- Original Message -----
From: "blake shepherd" <blake@b...>
To: "'AZ_VJC'" <AZ_vjc@yahoogroups.com>
Sent: Friday, February 02, 2001 2:40 PM
Subject: [az_vjc] CJ Dana 30 broken....Help!!
>
> Today I removed the diff cover on my dana 30 only to find that the ring
gear
> has a broken tooth. The gear is missing about 1/2 of one tooth (pinion
gear
> is fine). Plus the tooth was not in the case or the fluid........ hmm.
> Before I spend alot of money fixing the dana 30, I would like to know what
> axles I can swap in its place. Will a YJ or TJ dana 30 bolt in or do they
> have a reverse rotation? I have heard of people swapping in scout or
maybe
> early bronco axles. I am looking for help. Does anyone have an entire
dana
> 30 or any other axle that you have laying around that would fit? Any
> comments are appreciated.
>
> TIA
>
> Blake 1980 CJ5 35" BFG'S Chevy 305
>
>
>
>
18251 From: AzVJC Website <azvjc@a...>
Date: Fri Feb 2, 2001 11:08pm
Subject: [TR] Box Canyon - Sunday, February 4, 2001
Hello All,
This is an automated message from the website, please do not reply to it!
Ray B. is leading a Box Canyon trail run on Sunday, February 4, 2001.
When: Meet at 10:00am...air down and hit the trail by 10:45.
Where: Dirt lot just south of the RR Tracks at the North end of
Florence. (Near mile Marker 136 on Hwy 79) Right on Price
Rd.
Rating: 3.0
Length: All Day
CB Channel: 4
We will run through Box Canyon as a warm up, then on to the
Coke Ovens. Gonna give this one more try Hoping for co-
operation from Mother Nature.
Click Here To Add Your Name to the List or For More Information
Thank You,
- The AzVJC Website
18252 From: <jeep108@h...>
Date: Fri Feb 2, 2001 11:24pm
Subject: Good deal on d30 & d44
In todays az rep in the stuff under $100 there was a d44 rear ls rear
out of a 97 tj with 3:55s and front d 30 for $50 each.Good deal if
someone needs one.
Ken
18253 From: Chris <i_shence_2000@y...>
Date: Sat Feb 3, 2001 0:29am
Subject: Trail Rating
Hello,
I'm a new member, I just bought a 98 Wrangler yesterday. I've
passengered many off-roading trips with my friends, but now I finally
get to drive the trails for myself. Everything is really new to me,
I've reading all the info I can on safe 4x4in' and looking at the
photos and stuff. I am curious on trail ratings.. Whats the rating of
Senator Highway? Thats the road that runs from crown king to prescott.
I'm a huge fan of crown king and I hope to someday make the drive up
from pleasent myself. Check out my Crown king fan site, I'll be
updating it soon with recent photos from just last week, and soon
again with photos with my jeep :)
http://i-shence.com/crownking/
Thanks,
Chris benner
18254 From: DougB <azjeep@h...>
Date: Sat Feb 3, 2001 3:45am
Subject: Re: Trail Rating
Welcome aboard!
As to the trail from CK to Prescott...probably a class 2 to 2+. Fine for a
stock Jeep.
Doug
----- Original Message -----
From: "Chris" <i_shence_2000@y...>
To: <az_vjc@yahoogroups.com>
Sent: Saturday, February 03, 2001 1:29 AM
Subject: [az_vjc] Trail Rating
> Hello,
> I'm a new member, I just bought a 98 Wrangler yesterday. I've
> passengered many off-roading trips with my friends, but now I finally
> get to drive the trails for myself. Everything is really new to me,
> I've reading all the info I can on safe 4x4in' and looking at the
> photos and stuff. I am curious on trail ratings.. Whats the rating of
> Senator Highway? Thats the road that runs from crown king to prescott.
> I'm a huge fan of crown king and I hope to someday make the drive up
> from pleasent myself. Check out my Crown king fan site, I'll be
> updating it soon with recent photos from just last week, and soon
> again with photos with my jeep :)
>
> http://i-shence.com/crownking/
>
> Thanks,
> Chris benner
>
>
>
>
>
>
18255 From: Jon Loveless <jonloveless@m...>
Date: Sat Feb 3, 2001 5:08am
Subject: ToyBox
Damon Flippo (ToyBox) operates out of his father-in-laws battery shop off 21st Street and Deer Valley Parkway. His web site is www.ToyBoxoffroad.com . He does stock some parts.
Jon Loveless
(480) 816-6240
18256 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 6:33am
Subject: RE: Trail Rating
Welcome aboard, Chris.
It has been a few years since I was on that part of the Senator near the
Prescott end, but when I last was, I ran it in a stock XJ....pretty scenery,
easy road.
Stu Olson N7QJP
Phoenix, AZ DM33vm
http://www.stu-offroad.com
http://www.qsl.net/n7qjp
http://www.users.uswest.net/~solson8
Developer of VKE Digital Voice Keyer
-----Original Message-----
From: Chris [mailto:i_shence_2000@y...]
Sent: Saturday, February 03, 2001 1:30 AM
To: az_vjc@yahoogroups.com
Subject: [az_vjc] Trail Rating
Hello,
I'm a new member, I just bought a 98 Wrangler yesterday. I've
passengered many off-roading trips with my friends, but now I finally
get to drive the trails for myself. Everything is really new to me,
I've reading all the info I can on safe 4x4in' and looking at the
photos and stuff. I am curious on trail ratings.. Whats the rating of
Senator Highway? Thats the road that runs from crown king to prescott.
I'm a huge fan of crown king and I hope to someday make the drive up
from pleasent myself. Check out my Crown king fan site, I'll be
updating it soon with recent photos from just last week, and soon
again with photos with my jeep :)
http://i-shence.com/crownking/
Thanks,
Chris benner
18257 From: Ken Borer <kborer@i...>
Date: Sat Feb 3, 2001 7:22am
Subject: Box Canyon on Sunday
Ray,
Thanks for the reschedule on this trip - we will see you in the morning.
Ken
76 CJ-5 304 V8
2 1/2" Sagging Lift - 4" Superlift soon
33 X 12.5 on 15 X 10 Rims
Open Both Ends for now
18258 From: TRobertsRN <TRobertsRN@e...>
Date: Sat Feb 3, 2001 7:36am
Subject: Fw: springs
----- Original Message -----
From: TRobertsRN <TRobertsRN@e...>
To: FSJ List <fsj-list@l...>
Sent: Saturday, February 03, 2001 8:30 AM
Subject: springs
Sorry I have been so slow to respond to those interested in my springs from
the 78 Cherokee. I have been very ill, can barely get out of bed, have not
slept in 3 days. Therefore I have not been able to check on shipping price.
I did notice that a couple of you that were interested were in Arizona.
Right now it would make my life a lot easier if one of you could come by and
pick them up.
Thomas Roberts
78 Cherokee WT
Mesa, Arizona
18259 From: <Jeepguy@z...>
Date: Sat Feb 3, 2001 10:11am
Subject: fire stick
Can you paint a Firestick ant with rustoleum paint? does it have any
adverse effects?? I know it is no sat dish, but hey... you never
know!! :)
18260 From: <Jeepguy@z...>
Date: Sat Feb 3, 2001 10:48am
Subject: Firstwater Closed!!
Okay they were easy trails, but fun no less! The Forrest service was
out there putting up the barbwire fences. They had raked the trails
to loosen up the dirt, and put big mounds of dirt in front of the
fences (as if that would stop the almighty jeep)! Anyway, they are
pretty tame hills, but great for beginners and they are gone... all
gone!! :(
18261 From: <sharxjeep@c...>
Date: Sat Feb 3, 2001 6:16am
Subject: Squeeze rock
Has anyone run Squeeze Rock at Sycamore Creek and could they give me some
info on it. Some friends and I were going to go out that way tomorrow and
would like to check it out. Any info would be greatly appreciated, thanks.
Sharky
18262 From: Kelly McCormick <KellyMC@p...>
Date: Sat Feb 3, 2001 3:01pm
Subject: Items for Sale
I still have that Warrior roof rack for sale, in addition to some other
parts the are not neccessarily all for jeeps.
I have four 31" Mudders w/ 6 lug-$500
Any stock parts off a 97 TJ, like springs, snocks, trac bar, tire carrier,
someone is just welcome to have.
I also have a silver camper shell of a 92 Toyota for $500.
Well let me know,
Thanks Kelly
18263 From: Eric Herring <herring@u...>
Date: Sat Feb 3, 2001 3:31pm
Subject: RE: fire stick
I don't know but they do sell them in different colors.
Eric Herring 92XJ
-----Original Message-----
From: Jeepguy@z... [mailto:Jeepguy@z...]
Sent: Saturday, February 03, 2001 11:11 AM
To: az_vjc@yahoogroups.com
Subject: [az_vjc] fire stick
Can you paint a Firestick ant with rustoleum paint? does it have any
adverse effects?? I know it is no sat dish, but hey... you never
know!! :)
18264 From: Greg Mobley <greg85268@y...>
Date: Sat Feb 3, 2001 4:33pm
Subject: Help with teraflex quick disconnect
18265 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 4:46pm
Subject: RE: Help with teraflex quick disconnect
Sure.....but you have to ask a question first!
Stu Olson N7QJP
Phoenix, AZ DM33vm
http://www.stu-offroad.com
http://www.qsl.net/n7qjp
http://www.users.uswest.net/~solson8
Developer of VKE Digital Voice Keyer
-----Original Message-----
From: Greg Mobley [mailto:greg85268@yahoo.com]
Sent: Saturday, February 03, 2001 5:33 PM
To: Jeep Club
Subject: [az_vjc] Help with teraflex quick disconnect
18266 From: Greg Mobley <greg85268@y...>
Date: Sat Feb 3, 2001 5:03pm
Subject: HELP WITH TERAFLEX QUICK DISCONNECT
Hi everyone
I recently had a Teraflex 3 inch lift kit put on and I want to put Teraflex quick disconnects on by myself shop wants $70.00 to install it don't look that difficult what advice could everyone give me.
Thank you
Greg
18267 From: Stu Olson <solson8@q...>
Date: Sat Feb 3, 2001 5:10pm
Subject: RE: HELP WITH TERAFLEX QUICK DISCONNECT
Greg,
I'll pass along a spot on my web site you might find helpful.
My install comments and some pics of the Tera QDs at http://www.stu-offroad.com/98jeep_lift/tj_lift2.htm
Feel free to snoop around....you might find some other helpful information.
Later..........Stu
Stu Olson N7QJP
Phoenix, AZ
http://www.stu-offroad.com
http://www.users.uswest.net/~solson8
-----Original Message-----
From: Greg Mobley [mailto:greg85268@yahoo.com]
Sent: Saturday, February 03, 2001 18:04
To: Jeep Club
Subject: [az_vjc] HELP WITH TERAFLEX QUICK DISCONNECT
Hi everyone
I recently had a Teraflex 3 inch lift kit put on and I want to put Teraflex quick disconnects on by myself shop wants $70.00 to install it don't look that difficult what advice could everyone give me.
Thank you
Greg
18268 From: <sharxjeep@c...>
Date: Sat Feb 3, 2001 0:37pm
Subject: Squeeze Rock
Has anyone run Squeeze Rock at Sycamore Canyon and could they give me some
info on it. Some friends and I were going to go out that way tomorrow and
would like to check it out. Any info would be greatly appreciated, thanks.
Sharky
18269 From: Larry T. <lwt002@a...>
Date: Sat Feb 3, 2001 5:54pm
Subject: Member sighting !!
White lifted TJ, Northbound, Alma School North of Southern about
11:20+-AM. Sweet ride!
I was in the black TJ. I waved but it was probably too late for you
to see.
Larry T.