SYE Installs

[jeepin_in_az]

Hello all,

There are a couple people that will be installing SYE's soon. I have done 5-7 of them, so I will take the helm of helping. If you are interested in helping, learning, or just hanging out, post here. I am not sure of a date yet, prob in the next couple of weeks.

Is there anyone in the Chandler area with a 2 car garage that we can do both at the same time? Will make it go faster for one, takes about 3 hours each.

Thanks,

[3timejeepin]

i have a 3 car garage we could do it in, with a good amount of tools maybe you could swing by first to approve?

[jeepin_in_az]

Originally posted by 3timejeepin
i have a 3 car garage we could do it in, with a good amount of tools maybe you could swing by first to approve?


That would be great. My cell phone is a little dead today, give me a call later today....you should have it in the e-mails.

[Y2K-XJ]

I'm In Chandler Arizona ave and Knox w/ 2 car garage, compressor and plenty o tools But no Beer LOL so someone needs to bring it! Rob B

[FlexyXJ]

3 hours?????? DAMN, Are you guys nappin???? 25 min to remove case, 15 to dissasemble case and install SYE kit, 5 to clean and re-silacone and re assemble, 2 to slam a quick brew and 25 to re-install and fill...= 1 hour 12 min..........damn, hope you guys dont work on flat rate.......:)


Joe

[3timejeepin]

you wana come help us then?? whats the story guys we gonna get this to move forward?

[BRUZR]

Originally posted by jeepin_in_az

Is there anyone in the Chandler area with a 2 car garage that we can do both at the same time? Will make it go faster for one, takes about 3 hours each.

Thanks,

Yeah, 'cause there's NO WAY to even fit one Jeep in your garage, much less two!!! LOL :D :D :D

[jeepin_in_az]

Originally posted by FlexyXJ
3 hours?????? DAMN, Are you guys nappin???? 25 min to remove case, 15 to dissasemble case and install SYE kit, 5 to clean and re-silacone and re assemble, 2 to slam a quick brew and 25 to re-install and fill...= 1 hour 12 min..........damn, hope you guys dont work on flat rate.......:)


Joe


I didn't say I was going to do them, I said I would supervise:D (means watch what they are doing and drink beer).

Most likely take 3 hours for BOTH, so, I am just about 20 min. slower than you.

I leave the case in the Jeep too.

[jeepin_in_az]

Originally posted by BRUZRs_Daddy
Yeah, 'cause there's NO WAY to even fit one Jeep in your garage, much less two!!! LOL :D :D :D



:D I fit my Jeep in there, when I moved stuff around....

[FlexyXJ]

I am there.... Just supply me with air, beer. I will bring tools. When is this gonna happen????? I take the case OUT. I have seen bad things when you leave them in.....Like crunching noises.....:)


Joe

[jeepin_in_az]

Originally posted by FlexyXJ
I am there.... Just supply me with air, beer. I will bring tools. When is this gonna happen????? I take the case OUT. I have seen bad things when you leave them in.....Like crunching noises.....:)


Joe


I don't know, not sure if he purchased the kit or not.

I will check with my other friend to see if he is ready.

[3timejeepin]

hey mike the vibes on my jeep are getting bad, i think i will do the cut and tap or whatever you all call it, have you ever installed one? any word on your friend?

[jeepin_in_az]

I have not done a hack and tap, wonder if Joe has?


Flexxy?

My other friend is ready, 2 weeks from this Sat is when we are avail, so Jan 31st.

[3timejeepin]

ok sounds good, what kit did he get??

[jeepin_in_az]

Bayou Geep kit.

[frog]

flexy joe is the cut and tap master

[Hackle]

Mike and Joe just a reminder Jan 31st is the Table Mesa Clean-up.
Jim F.

[3timejeepin]

joe west?? and i cant do the slip yoke i wana go to the table clean up i signed up already thanks for the reminder.

[jeepin_in_az]

Originally posted by 3timejeepin
joe west?? and i cant do the slip yoke i wana go to the table clean up i signed up already thanks for the reminder.

Joe West, LOL....no Flexxy = Joe Daro

[Antman]

Originally posted by 3timejeepin
hey mike the vibes on my jeep are getting bad, i think i will do the cut and tap or whatever you all call it, have you ever installed one? any word on your friend?

The hack and tap is realitively simple. I did mine with a metal cutting blade installed on a circular saw. Just be sure to follow the RE instructions and be sure to get good (titanium) drill bits and a good American made tap and use the cutting oil liberally. OH! and measure twice. The scary part is cutting the shaft.....it just doesn't seem natural to do that.

[Y2K-XJ]

Hey Joe Sell me that SYE you got and Help me do it also mr. nice guy !! LOL
Like I said Guys Im in Chandler and have 2 CG, air and tools.. and most of the time Cold beer..and Nice stereo!! LOL

[baldwinwb11]

Check this price out
http://www.performanceoffroadcenter.com/oscommerce/product_info.php?cPath=37_42&products_id=153&osCsid=2fa5ad5a8a4ecf8fa1349e47f858ee7a

[jeepin_in_az]

Check this price out
http://www.performanceoffroadcenter.com/oscommerce/product_info.php?cPath=37_42&products_id=153&osCsid=2fa5ad5a8a4ecf8fa1349e47f858ee7a


Linky no workie....:D


EDIT: Nevermind, it worked.

That is a smokin' deal!

I paid $159 for mine 3 years ago...

[phoen1c1an]

I know this is a dumb question, and I think I already know the answer, but I'll ask it anyways.

If I put in a SYE, can I get rid of my TC drop? :confused:

[baldwinwb11]

I know this is a dumb question, and I think I already know the answer, but I'll ask it anyways.

If I put in a SYE, can I get rid of my TC drop? :confused:

and Add a CV drive shaft and you should be good.

[ScoobyDoo]

YEP , that is the big reason to do it :D

You can get the RE Hack-n-Tap on Ebay for $88
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=7939587054&rd=1&sspagename=STRK%3AMEWA%3AIT